Roof Seals & Roofing Underlayment Suppliers
Roof Sealing Membranes
Peel & Seal™ is the original, self-stick roll roofing specifically designed for low slope applications, both residential and commercial.
Composed of a patented formula (consisting of laminated aluminized foil, high-density polymer films and a thick layer of rubberized asphalt), Peel & Seal provides a long lasting, durable, maintenance-free roofing seal surface.
From dormers, residential sunroom additions, "open" porches, and mobile home roofs, to industrial and agricultural buildings where low slope roofs are common place, Peel & Seal is an excellent solution for these applications. The self-adhering, weatherproof, reflective surface not only forms a highly effective barrier to the elements, but also limits solar heating to help keep the temperature of building interiors significantly cooler.
Applying Peel & Seal is easy. No tar, torches, mops, glues, tapes, or fasteners are required…a scissors or knife and hand roller are the only tools needed. Following preparation of the surface, simply peel off the release paper, unroll Peel & Seal to the proper length.
Maintenance-free Peel & Seal will not crack or dry out after being applied, is available in a choice of finishes (aluminum, almond, white, and granite gray), and conveniently sized in 100 sq. ft. cartons in roll widths of 3”, 4”, 6”, 9”, 12”, 18” and 36”.
Peel & Seal is perfect for hundreds of uses ranging from full-roof sealing applications to patching gutters and vent pipes. Fully pliable and providing a secure seal at edges, corners and over gaps, it is ideal for roof areas that are often difficult to waterproof, including locations where ducts, vents, chimneys, or air conditioning units either protrude through, or are roof mounted.
Peel & Seal: The original, maintenance-free, energy efficient, economical, self-sealing roll roofing you can count on for any low slope/low pitch application…and warranted by MFM for 10 full years!
MFM ShingleStarter™ is a self-adhesive membrane that eliminates the need to cut shingle tabs. ShingleStarter comes with a seal strip to prevent wind uplift at the roof edge.
The peel and stick application allows fast installation, saving time and labor. The membrane is waterproof and self-sealing around nails and other penetrations. ShingleStarter may be adhered directly to the roof deck or to Wind & Water Seal™ self-adhering underlayments.
ShingleStarter is shipped in cartons of 8 individually wrapped rolls that are 7.2” X 33.5’.
Roofing Underlayments Supplies
MFM Wind & Water Seal™ is a self adhering waterproofing roof underlayment composed of a non-slip polymer film laminated to a rubberized asphalt adhesive. A split release film protects the adhesive and is removed as the roofing underlayment is installed. MFM Wind & Water Seal is engineered for use under all roofing materials including metal, asphalt, shake or concrete shingles, and clay tiles. MFM Wind & Water Seal adheres aggressively to most clean, dry substrates including metal, plywood, OSB, foam insulation, house-wrap, rigid vinyl and masonry.
The rubberized asphalt adhesive self-seals around punctures such as nails, screws and staples. This advanced system bonds to the substrate and seals around fasteners to limit damage caused by water penetration or leaks.
MFM Premium Wind & Water Seal™ is a self-adhering waterproofing underlayment membrane designed for extreme applications. It is composed of a tough multilayer high-strength polymer film coated with a layer of specially formulated rubberized asphalt adhesive. A release sheet protects the asphalt and is removed as the membrane is installed. To improve surface traction, a raised pattern has been embedded into the top of the polymer film.
Premium Wind & Water Seal roofing underlayment is engineered to be suitable for use under all roofing materials. The rubberized asphalt adhesive and the reinforced polymer film are formulated to work in higher temperature applications such as under metal roofing.
Premium Wind & Water Seal adheres aggressively to most clean, dry substrates including metal, wood, oriented strand board, foam board, vinyl and masonry.
IB-3™ is a self-adhering waterproof roof underlayment for shingles, tile, and other types of roofing. It is constructed from a strong layer of mesh bonded to rubberized asphalt and coated with black stone granules. Designed to be used as protection against leading edge ice dams, melting snow and wind-driven rain, IB-3 may also be used on valleys, eaves, ridges and anywhere an extra layer of protection is required.
IB-4™ is a self-adhering mineral surface underlayment which is applied directly to the roof deck to protect from leaks due to wind-driven rain or roof failure. The specially formulated rubberized asphalt adhesive seals around nails and forms a long-lasting barrier. IB-4 is backed with a protective release sheet which removes easily during application. The release sheet is perforated in the middle for easy valley applications. An adhesive selvedge ensures a water-tight seal between courses. IB-4 also has a one year exposure rating. IB-4 may be used under metal roofing if allowed by the metal roofing manufacturer.
These roofing underlayment and roofing seals are only a portion of our abundant building materials.